[Developers] Question Regarding VizLauncher

[prabath at phys.utb.edu]

Hi Dr.Goodale

Thank you for your reply. 

It was really helpful and I fix that problem, but i ran in to another conflict. When I open the HDF5 stream data file, it launch the OpenDx and it display following message.

--------------------------------------------------------------------------------
Starting DX executive
Memory cache will use 816 MB (50 for small items, 766 for large)
Begin Execution
Warning! The HDF5 header files included by this application do not match the
Begin Execution
version used by the HDF5 library to which this application is linked. Data
corruption or segmentation faults may occur if the application continues.
'HDF5_DISABLE_VERSION_CHECK' environment variable set, application will
continue.
Headers are 1.6.4, library is 1.6.3
server: accepted connection from client
 0:  worker here [11312]
--------------------------------------------------------------------------------



I am using hdf5-1.6.4 distribution (Platform RH9)


thank you.

prabath



Tom Goodale <goodale at cct.lsu.edu> wrote :

> Hi,
> 
> which web-browser are you using ?  You may need to setup the 
> helper-application by hand, as some of the newer browsers ignore the 
> .mime.types and .mailcap files.  Also you may need to make a soft link
> 
> ln -s Vizlauncher VizLauncher-streamed-hdf5
> 
> (assuming you are using unix) and associate the mime-type for streamed 
> hdf5
> 
> data/x-streamed-hdf5
> 
> with the VizLauncher-streamed-hdf5 application, as again, some of the 
> newer browsers, such as Mozilla, no longer seem to allow one to pass 
> useful arguments such as mime-type to the helper application.
> 
> I hope this helps,
> 
> Tom
> 
> On Thu, 19 May 2005 prabath at phys.utb.edu
> wrote:
> 
> &gt; Hi
> &gt;
> &gt; ** I am very sorry about my previous mail, for some reason it cut off half
> of it contents.
> &gt;
> &gt; I have a question regarding VizLauncher
> &gt;
> &gt; I am running some simulations using cactus, I am using HDF5 for out put.
> When I browse my simulation using web server, in the file section it shows
> streamed HDF5 data file. My question is how can I display my simulation data
> using OpenDx and VizLauncher.
> &gt;
> &gt; I already install OpenDx and set up the ImportHDF5 and ImportHDF5.mdf file
> paths according to OpenDx-HOWTO document. According to the VizLauncher-HOWTO
> file, I set up the mailcap and .mime.types files.
> &gt;
> &gt; Now I am in the section under 'Using VizLauncher' topic (in
> VizLauncher-HOWTO). But its not clear to me how to launch the VizLauncher with
> openDx. Should I save the Streamed HDF5 data file in to my file system and then
> run the VizLauncher ? Or
> &gt;
> &gt; Thank you for your time
> &gt;
> &gt; Prabath Peiris (Undergraduate Student)
> &gt; The Department of Physics and Astronomy
> &gt; UTB, Brownsville, TX
> &gt;
> &gt; ___________________________________
> &gt; NOCC, http://nocc.sourceforge.net
> &gt;
> &gt;
> &gt; _______________________________________________
> &gt; Developers mailing list
> &gt; Developers at cactuscode.org
> &gt; http://www.cactuscode.org/mailman/listinfo/developers
> &gt;

___________________________________
NOCC, http://nocc.sourceforge.net